夜夜躁狠狠躁日日躁婷婷小说,乳首视频,欧美日韩一二三四,无码中文不卡高清

濟南歌德瑞斯機械設備有限公司

咨詢熱線:
18678805065
歌德瑞斯

濟南歌德瑞斯機械設備有限公司,是窗門制造機器行業的一家集研發、設計、生產、銷售、服務為一體的綜合性公司。

查看更多+
歌德瑞斯

嚴格按照行業標準和出口標準組織生產。機器的優良品質和優異性能已被客戶廣泛認可。同時,公司繼續加大對產品研發的投入,以增強產品的核心競爭優勢。

查看更多+
歌德瑞斯

嚴格按照行業標準和出口標準組織生產。機器的優良品質和優異性能已被客戶廣泛認可。同時,公司繼續加大對產品研發的投入,以增強產品的核心競爭優勢。

查看更多+
您當前所在位置:首頁-新聞資訊-行業動態開齒穿條機操作 >
行業動態

開齒穿條機操作

發布時間:2025-03-28 來源:http:///

1.將開齒穿條機設備的電源線接到車間內380伏的空氣開關上,檢查電路接好

1. Connect the power cord of the toothed threading machine equipment to the 380V air switch in the workshop and check that the circuit is properly connected

從左邊數,左邊的三根黑色的是380伏火線、左邊第四根黃色的是零線。通電后如果發現“刀盤上升”是反的,那么要將左邊的三根黑線任意交叉換一下。調整好電機的方向。

Counting from the left, the three black wires on the left are the 380V live wires, and the fourth yellow wire on the left is the neutral wire. If it is found that the "cutter head rising" is reversed after power on, then the three black lines on the left should be crossed and replaced at will. Adjust the direction of the motor.

12

2.調整和安裝好兩面的托料平臺。

2. Adjust and install the material support platforms on both sides.

3.先放入一根型材,用手調整該機頭的左右移動手輪,將“導向定位塊”調整到機器出條槽口和鋁型材穿條槽口一致;如需要上下調整則按動“刀盤上升”和“刀盤下降”來調整機頭的高度。

3. First, place a profile and adjust the left and right movement handwheel of the machine head by hand. Adjust the "guide positioning block" to match the machine strip slot and the aluminum profile strip slot; If you need to adjust up and down, press "cutterhead up" and "cutterhead down" to adjust the height of the machine head.

4.再放入上面的兩根開好齒的鋁型材,調整后面托料架子上的“定位板”,頂住鋁型材。

4. Put in the two toothed aluminum profiles on top, adjust the "positioning plate" on the material rack at the back, and press against the aluminum profiles.

5.用人工將隔熱條順導向槽口送入鋁型材槽口內一點。

5. Manually guide the insulation strip into the slot of the aluminum profile to a point inside the slot.

6.踩下設備上的腳踏開關,齒刀加壓轉動,將隔熱條高速送入鋁型材槽口,穿條完畢后,松開腳踏開關。

6. Step on the foot switch on the device, apply pressure and rotate the toothed knife, and quickly feed the insulation strip into the slot of the aluminum profile. After threading the strip, release the foot switch.

7.重復以上步驟,加工下一根鋁型材。

7. Repeat the above steps to process the next aluminum profile.